Latest anti corrosive coating Tenders | Government anti corrosive coating Tenders

State Government

CTN :43563694

23 Jan, 2026 NA

Pune - Maharashtra

Tender For repair and overhauling service - sushobhikaran va sudharna tadmajla classroom; sushobhikaran va sudharna tadmajla classroom; yes; buyer premises-1 providing and fixing classroom table made of 19 mm thick plywood, finished with thick decorative laminate of approved shade and make on top surface and balancing laminate on bottom. sq.ft 700 table size shall be 14 feet (l) 2.5 feet (w) with suitable internal framing, stiffeners, and supports to ensure rigidity and durability. all exposed edges shall be finished with hardwood lipping. 2 providing and fixing step-up platform table made from 19 mm thick plywood, finished with decorative laminate on top and balancing laminate on underside. sq.ft 1408 structure shall be strong enough to withstand continuous foot traffic, with proper support framing and anti-warping construction. edges to be finished with hardwood lipping. complete in all respects including material, labour, fixing, and finishing as per site requirement. 3 providing and fixing professor table made of 19 mm thick plywood, finished with decorative laminate on top surface and balancing laminate below. sq.ft 40 table shall be ergonomically designed with appropriate height and working space suitable for faculty use. edges shall be properly finished with hardwood lipping. 4 providing and fixing lecture podium made of thick plywood, finished with thick decorative laminate on all exposed surfaces. sq.ft 32 design shall be suitable for classroom / lecture hall use with slanted top surface for documents. edges to be properly finished and rounded for safety. complete including all fittings, labour, and finishing. 5 providing, making and fixing 35 mm thick flush door shutter made from solid core , laminated with decorative laminate on both sides of approved make and shade. no 4 door shall include all necessary hardware fittings such as hinges, handles, tower bolt, door stopper, and locking arrangement of approved make. 6 providing and fixing wall-towall floor carpet of approved quality, colour, and thickness suitable for classroom use, laid over prepared floor surface. sq.ft 1664 carpet shall be fixed using approved adhesive, properly stretched, aligned, and finished to avoid wrinkles and gaps. chairs for class room 7 providing and fixing classroom chair made of heavy-duty ms tubular frame, properly welded, ground smooth and finished with powder coating of approved colour to ensure corrosion resistance and durability. nos 120 8 providing and fixing faculty chair made of heavy-duty nylon base , finished to resist corrosion and wear, suitable for continuous institutional use. the chair shall be nos 4 ergonomically designed, with medium back support, moulded pu foam cushioned seat and back, upholstered with fabric of approved make and shade. false ceiling for class room 9 providing and fixing 2 feet 2 feet grid false ceiling system consisting of approved quality pre-painted gi framework, including main runners, cross tees, wall angle, suspenders, dash fasteners, and all accessories, suspended from rods, complete in all respects. sq.ft 1664 electrical work for class room 10 supply and installation of electrical conduits, pipes, copper wiring, and cabling of approved make and size including junction boxes, accessories, testing, and commissioning. nos 1664 providing and fixing of switch and socket supply and installation of 2 2 led panel light fixtures of approved wattage suitable for false ceiling mounting. smart interactive panel and audio system 11 supply, installation, testing, and commissioning of smart interactive flat panel display (ifpd) suitable for classrooms. nos 4 having features follows:- led interactive flat panel multi-touch technology built-in operating system & hardware audio & connectivity 12 pa amplifier shall be solidstate type, with inbuilt tone control, microphone and auxiliary inputs, master volume control, and overload protection. nos 4 13 providing, supplying, installing, testing and commissioning podium m

corporations/Associations/Others

CTN :43582195

09 Feb, 2026 3.23 Crore

Kanpur - Uttar Pradesh

Tender For providing of custom bid for services - in sourcing to maintain the concentration of pre treatment process tanks along with parameter of powder coated components in the powder coating plant wc06 along with material chemicals supply for a period of 1 year

CTN :43345126

05 Feb, 2026 NA

Jalgaon - Maharashtra

Tender For corrigendum : supply of powder coating booth spares and consumable d d - filter final 500 series , filter 36 powder grid plus , o-ring, silicone 0. 5 x 0. 625 in , r ring 113 slcne cond duro 70 , pump encore hd assy , kit hdlv pump fluid tube no 1057258 , washer l k m part no 983401 , seal upper y block part no. 1604072 , o ring slcne . 375 x . 500 x . 063 part no. 940126 , cone male elnow, 6mm t x 1 part no. 972126 , o ring, slcne . 750 x 1. 000 x . 125 part no. 942101 , o ring slcne . 750 x 1. 000 part no 942106 , o ring slcne 1. 000 x 1. 250 part no. 942146 , o ring slcne . 875 x 1. 062 part no. 941185 , o ring slcne . 625 x . 812 part no 941145 , kit check valve hd or xd pump part no. 1625733 , seal bulkhead 7 by 8 - 16 thread part no 1023695 , ring sealing 1 by 4 part no 955063 , wheel swivel part no 7764058 , clamp toggle jupiter part no. 7765017 , nozzle venturi jupiter part no. 7762500 , pump body transfer part no. 7762502 , pump assy trans part no. 7760107 suitable for nordson make hd powder coating booth. , kit hose adapter part no. 1106200 , o ring viton blk part no. 940157

CTN :43563046

23 Jan, 2026 NA

Kota - Rajasthan

Tender For supply of file cabinet , extra cabinets , powder coating , mild steel 404 , wheels

Central Government/Public Sector

CTN :43563600

02 Feb, 2026 NA

Raigad - Maharashtra

Tender For tender for supply of motor fan for 0.75kw, 1500 rpm, 80s frame motor. coating: the fan shall be powder coated. cooling fan m.o.c.m.s. sheet thickness shall be minimum 3 mm.

Central Government/Public Sector

CTN :43591899

09 Feb, 2026 NA

Kozhikode - Kerala

Tender For supply of 12 door industrial locker overall dimensions (minimum):height: 1950 mm(excluding pedestal height 125 mm) width: 2090 mm - approx, depth: 500 mm. individual compartment size (minimum):height: 450 mm, width: 600 mm. material: constructed using 0.8 mm thick crca (cold rolled close annealed) sheet. compartment base using 1mm thick crca. locker to be finished with high-quality powder coating for corrosion resistance and durability. additional requirements: the locker should be divided into 12 equal compartments of 3 x 4. each compartment should have a secure locking mechanism. suitable ventilation slots and name tag holders may be provided on each door. electro plated handle. [ warranty period: 24 months after the date of delivery ]

Corporations And Associations And Others

CTN :43514578

16 Jan, 2026 33.81 Lacs

Delhi - Delhi

Tender For supply and installation of open gym equipments and construction of epdm flooring under open gym equipment in shahdara south zone, under mplads funds for various locations of parks in municipal corporation of delhi. - supply and installation of open gym equipments and construction of epdm flooring under open gym equipment in shahdara south zone, under mplads funds for various locations of parks in municipal corporation of delhi., seated puller /pull chair made from c class g.i pipe. dimensions: - 1900mm (length) x 740mm (width) x 1920mm. (height). safe area:- 1.2mtr x 3mtr. seated puller equipment made up of c class g.i. pipe of different nb.nb stands for nominal bore sizes i.e. internal diameter of pipe in millimeters. the center pipe is of 100nb made from c class g.i. pipe. bottom support is of m.s. round plate of dia 250 mm & 10mm thickness welded. all linkages are made up of 25nb c class g.i. pipe. the handle frame is of 32nb c class g.i. pipe. the seat frame is of 32nb c class g.i. pipe. to build structure bushes are used which are made from seamless pipe of 60mm o.d. and 5mm thickness as well as 60mm diameter solid bar bush used. the foundation used for fixing is a structure and made from center pipe of g.i. of 80 nb c class. welded with m.s. round plate of dia 250 mm & 10mm thick. main pipe supported with 25 mm x 25mm m.s. angles of 3 mm thickness and 20mm x 40mm crc square pipes of 3mm thickness. foundation cover closing cap is made from injection moulded plastic lldpe / hdpe. the seats and back rests are fitted on the outer frames are made up of m.s. sheet of size 330 mm x 300 mmx2mm thickness and deep drawn and pressed in tools and dies to have uniform radius of 20 mm with no sharp edges.closing caps are made up of from injection moulded plastic lldpe / hdpe.pins used of diameter 25mm and 17mm are made up from sae 8620 bright material. the bearings used are of 6205 2rs1 and 6203 2rs1 permanent lubricated sealed bearing of reputed brand.high tensile steel with galvanized nuts & bolts are used for assembly.thecirclips used for assembly are of a16. the gym equipment shall be finished smooth with a primer coating of atleast 40 micron followed by epoxy based powder coating with polyster powder coating of at least 60 to 70 micron thickness using exonobel / berger make paints or its equivalent paints. the holding down/fixing of gym equipments shall be emboded in cement concrete in the ratio of 1:2:4 (1cement : 2 coarse sand :4 stone agg. 20mm nominal size)., cross trainer /elliptical exerciser dimensions: - 1320mm (length) x 600mm (width) x 1750mm. (height). safe area: - 1.77 x 1.2mtr. cross trainer equipment made from c class g.i. pipe of different nb.nb stands for nominal bore sizes i.e. internal diameter of pipe in millimeters. the main frame pipes are of 80nb c class g.i. pipe with single bend pipe with 250mm radius. the bottom support of m.s. round plate of dia 250 mm & 10mm thick. the handle frame is made up of 25nb c class g.i. pipe. the foundation used for fixing is a structure and made from center pipe of g.i. of 80 nb c class welded with m.s. round plate of dia 250 mm & 10mm thick. main pipe supported with 25 mm x 25mm m.s. angles of 3 mm thickness and 20mm x 40mm crc square pipes of 3mm thickness. to build structure bushes are used which are made from m.s. seamless pipe of 60mm od with 5 mm thickness. the footrests are made from injection moulded plastic lldpe / hdpe. closing caps are made up of injection moulded plastic lldpe / hdpe. pins used of diameter 35mm, 25mm, and 17mm are made up from sae 8620 bright .the bearings used are of 6007 2rs1 62052rs1 and 62032rs1 permanent lubricated sealed bearing of reputed brand. high tensile steel with galvanized nuts and bolts are used for assembly. the gym equipment shall be finished smooth with a primer coating of atleast 40 micron followed by epoxy based powder coating with polyster powder coating of at least 60 to 70 micron thickness using exonobel

CTN :43529775

31 Jan, 2026 NA

Pune - Maharashtra

Tender For supply of gym equipment and other associated fitment items c c -treadmill , elliptical cross trainer , spin bike , air rower , lat pull down row , seated chest press , shoulder press , seated calf machine , 45 degree leg press , half rack , leg curl extension , olympic incline bench , olympic decline bench , olympic flat bench , power sled , adjustable bench , abductor or adductor , dumbbell rack , rubber round dumbbell 2. 5 kg , rubber round dumbbell 05 kg , rubber round dumbbell 7. 5 kg , rubber round dumbbell 10 kg , rubber round dumbbell 12. 5kg , rubber round dumbbell 15 kg , rubber round dumbbell 17. 5kg , rubber round dumbbell 20 kg , rubber round dumbbell 22. 5kg , rubber round dumbbell 25kg , rubber round dumbbell 27. 5kg , rubber round dumbbell 30 kg , maxim black rubber coated plate 2. 5 kg , flex colour rubber bumper plate 5 kg , flex colour rubber bumper plate 10 kg , flex colour rubber bumper plate 15 kg , flex colour rubber bumper plate 20 kg , flex colour rubber bumper plate 25 kg , weight plate tree , 7ft olympic barbell , 4ft straight olympic barbell , 4ft curl olympic barbell , hammer multi grip bar , deadlift hex trap shrug barbell , barbell holder 9 pieces , skipping rope , balance board , latex resistance bands-m , latex resistance bands-l , bosu ball with plastic base , laying power cable for electrically powered equipment a , provision of cabling work for hvac units , hanging and linear fixtures , concealed and surface fixtures , power control and distribution units , db box with circuit breakers , powder coating on structural members , branding on walls , signages for equipment usage guidelines , 8ft height single glazed partition , single leaf glass door with hardware , 6 mm new mirror with installation on ply paneling , 18mm ply framing with 12 mm ply base for mirror paneling , partition work above glass partition , acp paneling at entrance , 20 mm rubber flooring roll in gym , 6mm specialised spc flooring in studio

CTN :43463693

21 Jan, 2026 4.64 Lacs

Thiruvananthapuram - Kerala

Tender For one panchayath one playground- thanniyam stadium in kallara grama panchayath in vamanapuram lac, thiruvananthapuram- supply and installation of outdoor gym and sports equipment - outdoor gym equipments, od252260/2025-2026 : horse rider - supply and installation of horse rider having the following specifications:dimensions: (l x w x h) 1140 x 400 x 1400 mm. main frame - 114 mm od b class gi pipe. foundationplate m.s. round plate of 250 mm & 8 mm thick. foundation cover cap - dome shape of pp / nylon /hdpe material. remaining frame is made by 48 mm od ?b? class gi pipe. seat frame ?is made by 48mm od ?b? class gi pipe. seat position must be horizontal to 110 -120 degree. link - made up of 48 mm od ?b? class g.i. pipe. angle between link and ground position is 10-20 degree. handle - 33 mm od ?b? class gi pipe. paddle vertical support - 60 mm od ?b? class gi pipe. handle frame- 42 mm od ?b? class gi pipe dually bending design. foot pipe - 33 mm od ?b? class gi pipe. support frame ? 10 mm thick ms flat is used. seat- dimension 320 x 270 x 100 mm blow moulded wall thickness 4mm material hdpe.bearing bush closing cap ? pp / nylon / hdpe material. foundation stool: made from main pipe 88 mm od m.s pipe and top support of m.s. round plate of 250 mm & 8 mm thickness is welded at top. square tube of 30 x 30 x 2 mm must be used to support center pipe. height of stool is 3 ft.foundation stool is embedded in c.c. stock below ground level. bearing - use is 6005 permanent lubricated reputed brand.bearing bushes - 60mm od seamless pipe. pin ? made of 25 mm m.s. bright bar. grips - high quality rubber 46 mm od. circlips ? a 24 circlips are used for assembly. coating - best quality of powder coating 60 to 70 micron. safety instructions and exercise chart - start &finish position stick on product. all joints must be welded as per is standards and zinc primer paint should be applied at all the welding points prior to finishing. (foundation shall be m20 cc and design shall be approved by the engineer-in -charge before installation.), od252261/2025-2026 : back extension - supply and installation of back extension having the following specifications: dimensions: (l x w x h) 1060 x 730 x 990 mm. main frame - made from 88 mm od ?b?class g.i. pipe. foundation plate ? m.s. round plate of 250 mm & 8 mm thick. leg support - 42 mm od ?b? g.i pipe. seat rest pipe ? 42 mm od ?b? class g.i pipe. handle pipe ? 33 mm od ?b? class g.i pipe.footrest - cast iron 124 x 296 x 5 mm thick and m.s plate of 3 mm thick used to support it. footrest pipe ? 42 mm od ?b? class g.i pipe and 80 x 40 mm ms rectangular pipe. closing cap ?pp / nylon / hdpe material. seat ? 360 x 300 x 2 mm thick m.s. seat with corner fillet for safety. grips - high quality rubber 46 mm od. foundation stool: made from main pipe 88 mm od m.s pipe and top support of m.s. round plate of 250 mm & 8 mm thickness is welded top. square tube of 30 x 30 x 2 mm must be used to support center pipe. height of stool is 3 ft. foundation stool is embedded in c.c. stock below ground level. coating - best quality of powder coating 80-120 micron. safety instructions and exercise chart - start & finish position stick on product. all joints must be welded as per is standards and zinc primer paint should be applied at all the welding points prior to finishing. (foundation shall be m20 cc and design shall be approved by the engineer-in -charge before installation.), od252262/2025-2026 : cross trainer (double) - supply and installation of double cross trainer having the following specifications: dimensions: (l x w x h) 2280 x 550 x 1650 mm. main frame- made of 88 mm od ?b? class gi pipe dually bending design. foundation plate ? m.s. round plate of 250 mm & 8 mm thick. paddle vertical support - 42 mm od ?b? class gi pipe. handle - 33 mm od ?b?class gi pipe dually bending design. leg movement frame ? 50 mm x 50 mm x 2 mm thick square pipe. footrest - cast iron 124 x296 x 5 mm thick and m.s. plat